GreenFiber Attic Air Sealing Nationwide

GreenFiber Attic Air Sealing: The Houston Owner’s Guide

We stock and install GreenFiber-compatible attic air sealing in Houston, with most whole-attic air sealing jobs running between $900 and $2,400 depending on square footage and how many bypasses need addressing. Same-week scheduling is standard for us, and because we keep GreenFiber SANCTUARY and cellulose-compatible sealing materials on the truck, we can often start the work the day we diagnose it. Most Houston homeowners discover their air sealing has failed the same way: the upstairs runs five to seven degrees warmer than the thermostat setting in August, and the AC bill climbs even though nothing else changed.

Call (903) 447-8369

The part that fails is rarely a single component. Attic air sealing is a system: foam board blocking, spray foam around penetrations, and the GreenFiber blown-in insulation that sits on top of it all. When the sealing layer compresses, gaps around can lights and top plates, or settles below the R-value it was installed at, the whole attic stops performing. The insulation is still there. It’s just not doing its job.

Which GreenFiber Models This Applies To

If your attic has GreenFiber blown-in cellulose or fiberglass, the air sealing beneath it follows the same principles regardless of which GreenFiber product was installed. The two most common in Houston attics are GreenFiber SANCTUARY (their treated cellulose) and GreenFiber loose-fill fiberglass. SANCTUARY is denser and settles less over time; the fiberglass is lighter and more prone to air washing, where moving air erodes the insulation’s effective R-value along soffit edges.

Here’s the compatibility detail most people don’t know: GreenFiber SANCTUARY is designed to be installed at a specific density range, typically 3.5 to 4.2 pounds per cubic foot in an attic, and when it’s blown too light or too heavy, the air sealing performance drops off measurably. If a previous contractor blew it thin to stretch the material, you’ll see temperature striping across the ceiling, especially in older Houston ranches where the attic ventilation was never balanced. We can identify the issue with a density check and thermal scan, then re-seal and top up the insulation to spec.

For the sealing layer itself, OEM GreenFiber doesn’t make a proprietary “air sealing part” you can order. The sealing components come from the spray foam and foam board used around penetrations, the baffles along the soffit line, and the covers over recessed lights and bath fans. When we restore a GreenFiber attic, we’re matching those sealing materials to the depth and density of the existing GreenFiber product, not the other way around. Quality aftermarket foam and baffles work as well as anything branded, and we stock both to make that call honestly.

Signs Your GreenFiber Attic Air Sealing Is Failing

• Upstairs rooms run five or more degrees warmer than the thermostat setting. Warm air from the attic is finding its way into the living space through gaps the sealing layer should have closed. In Houston’s August heat, this shows up fast.
• You can feel a faint draft near can lights, attic hatches, or ceiling fans. These penetrations are the most common bypass points, and when the foam seal around them cracks or pulls away, air moves through on its own.
• Dust accumulates on ceiling surfaces and around vents faster than it used to. Loose-fill GreenFiber and attic dust get pulled into the living space by negative pressure when the sealing layer fails.
• Your AC bill jumped without a rate change or hotter-than-usual weather. When conditioned air leaks into the attic, the system runs longer to hold temperature. In Houston, a leaky attic seam costs real money every month.
• You notice uneven insulation depth when you look across the attic floor. Wind washing along the eaves or previous work that didn’t baffle correctly leaves bare or thin spots that break the thermal boundary.

Replacement Cost & What’s Included

Whole-attic air sealing on a typical 1,800 to 2,400 square foot Houston home runs between $900 and $2,400. Smaller jobs, like sealing a single room’s worth of penetrations or re-baffling one rafter bay, often land in the $300 to $600 range. The range depends on how many can lights, bath fans, plumbing stacks, and top plates need foam work, plus the depth and condition of the GreenFiber already up there.

Every quote is written before work starts. You’ll see the line items: baffle count, foam board sections, spray foam cans or board feet, labor hours, and disposal if we’re pulling compressed or contaminated material. No numbers change at the door. The Kingswell Guarantee covers the work for 365 days, in writing, and includes a free return visit if anything we sealed opens back up within that year. Glenn Hartley started this shop on the idea that a contractor’s word should hold up longer than the caulk.

DIY or Call Us?

Some parts of this job are safe to inspect on your own. You can open the attic hatch and check whether the insulation is evenly distributed, whether baffles are still stapled in place along the soffits, and whether you see daylight around vent pipes. You shouldn’t be moving blown-in GreenFiber around, cutting foam board, or spraying two-part foam overhead without proper respirator protection. Spray foam in an enclosed Houston attic in July is not a weekend project. The heat alone is enough to make the work dangerous.

Where homeowners get into trouble is thinking more insulation fixes a sealing problem. It doesn’t. If the bypasses are open, new GreenFiber on top just hides the failure. Call us at (903) 447-8369 and we’ll tell you what’s actually happening up there, then give you a written price before any work begins.

FAQs